D K 3 2 4 C - 1 5 A HITACHI NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1346| | | Capacity form/unform 150/ MB Heads 4| | | Seek time / track 17.0/ 7.0 ms Sector/track | | | Controller SCSI1 SINGLE-ENDED Precompensation Cache/Buffer 64 KB LOOK-AHEAD Landing Zone Data transfer rate 2.080 MB/S int Bytes/Sector 512 4.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit 48 MTBF h 150000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** HITACHI DK324C-21A JUMPER SETTING K2500468 18/7/91 +---------------------------------------------------------+ | 2 4 +-+--+ | JP3 +-+ | | | 1-3 | | | | | | +---+ | | | Terminator | | | | | |TM | | | | |114| | | | | | | | | +---+ | | | | | | | | | | | | JP2 JP1 | | | 15+--------1 9----1 | | | 16+--------2 +----2 +-+--+ +---------------------------------------------------------+ Other Side +-----------------------------------------------+--J6-----+ | | +-----1 +---+J2 | | 8-----2 | |Power | +---------+---+ | | | | | | | | | | | | | | | | | | | | | | | | | | +-------------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** HITACHI DK324C-21A JUMPER SETTING K2500468 18/7/91 Jumper Setting ============== The following jumpers are accessible to the user SCSI ID setting jumper J6 Pin 1 6 SCSI bus parity jumper JP2 Pin 3 4 Terminator power on/off JP3 Pin 1 4 MOTOR START/STOP setting jumper JP2 Pin 1 2 NOTE The DK324C jumpers other than listed above are installed by the manufacturer and must not be removed or replaced by the user. Never remove any of the "BLACK" factory set jumpers. These jumpers are unique to each drives. All jumpers should be set with power off. NOTE By using an extension cable from J6 connector, SCSI ID setting and LED are externally available. NOTE The terminator (TM114) of the DK324C other than the last drive of SCSI Daisy Chain MUST be removed. J6 SCSI ID setting jumper ------------------------- +----------+-----------------------+ | SCSI ID | 2(2) 2(1) 2(0) | | | 5-6 | 3-4 | 1-2 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ JP2 SCSI bus parity setting jumper ---------------------------------- JP2 3-4 CLOSED Disables SCSI bus parity (DEFAULT) 3-4 OPEN Enables SCSI bus parity JP3 Terminator power -------------------- +-----+ 4|xxxxx|3 +5Volt source for terminator is supplied only from the 2| o o |1 SCSI bus +-----+ +-----+ 4| o o |3 +5Volt source for terminator is supplied only from the 2|xxxxx|1 drive controller. +-----+ (DEFAULT) NOTE Terminator power source is supplied to the terminator resistor module from the host that pulls up the SCSI interface signals in the drive controller so that the SCSI bus lines will not be pulled down when DK324C power is turned down. JP2 MOTOR START/STOP Option jumper ---------------------------------- Pins 3 4 CLOSED The MOTOR START/SOP Option is not selected. The spindle motor is started when the DK324C power is turned on. NOTE When MOTOR START/STOP option is not used, the controller does not respond to the host for about 20 sec from Power turn-on to Drive Ready. Pins 3 4 OPEN The MOTOR START/STOP option is selected. The spindle motor can be started or stopped by using SCSI command. When the MOTOR START/STOP option is selected, the drive enters the motor stop state when its power is turned on. Use the Start/Stop Unit (1B) command to start or stop the drive. ********************************************************************** I N S T A L L ********************************************************************** HITACHI DK324C-21A JUMPER SETTING K2500468 18/7/91 Notes On Installation ===================== J6 Extension Cable ------------------ By using an extension cable from J6 connector, SCSI ID setting and LED are externally available. J6 7 Pin J6 8 Pin o-------------+<-----------o +-----------------------------------------+ | Connector part number on the cable side | +-----------+-------+---------------------+ |J6 Housing| Dupont|P/N 69305-002 (2pin) | +-----------+-------+---------------------+ |J6 Housing| Dupont|P/N 69307-004 (4pin) | +-----------+-------+---------------------+ |J6 Housing| Dupont|P/N 69307-006 (6pin) | +-----------+-------+---------------------+ |J6 Housing| Dupont|P/N 69307-008 (8pin) | +-----------+-------+---------------------+ |J6 Contact| | | | Socket | Dupont|P/N 77138-201 | +-----------+-------+---------------------+