D K 5 1 1 - 3 HITACHI NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/FH Cylinders 699| | | Capacity form/unform 30/ MB Heads 5| | | Seek time / track 30.0/ ms Sector/track 17| | | Controller MFM / ST506 Precompensation 300 Cache/Buffer KB Landing Zone 698 Data transfer rate 0.625 MB/S int Bytes/Sector 512 0.625 MB/S ext Recording method MFM operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM 3600 read/write W Acoustic dBA spin-up W ECC Bit MTBF h Warranty Month Lift/Lock/Park NO Certificates ********************************************************************** L A Y O U T ********************************************************************** HITACHI DK511 PRODUCT MANUAL K6600061 REV. 7 10/01/1985 +---------------------------------------------------------+ ++LED xxJP164 +-----+9 4--3 |XX ++ JP155 1-----8 | |JP117 |XX | 16------9 JP123 6--1 |XX J2 | 1+------+ PLO Write Prot.|XX | Velocity |XX | Gain 6--5 |XX | Write | |JP113 | | Protect | | |XX | SZ073 PCB REV. 3 +--1 |XX | Component Side +--4 |XX J1 | General xxJP70 | |JP68 |XX | Reset 8--1Drive |XX | Select |XX | +-------+ +-------+Term. | | + 5A | + IC | |xx | +-------+ +-------+ |XX | (POSN-P) TP27Ax xTP10A (GND) |XX J3 +---------------------------------------------------------+ +---------------------------------------------------------+ ++LED xxJP164 +-----+9 4--3 |XX ++ JP155 1-----8 | |JP117 |XX | 16------9 JP123 6--1 |XX J2 | 1+------+ |XX | |XX | 6--5 |XX | | |JP113 | | | | |XX | SZ073 PCB REV. 4 or 5 +--1 |XX | Component Side +--4 |XX J1 | 1xxx3 | |JP68 |XX | JP70 8--1 |XX | |XX | +-------+ +-------+Term. | | + 5A | + IC | |xx | +-------+ +-------+ |XX | (POSN-P) TP27Ax xTP10A (GND) |XX J3 +---------------------------------------------------------+ +---------------------------------------------------------+ ++LED xxx JP182A xxJP164 +-----+9 4--3 |XX ++ 1 3 JP155 1-----8 | |JP117 |XX | 16------9 JP123 6--1 |XX J2 | 1+------+ |XX | |XX | 6--5 |XX | | |JP113 | | | | |XX | SZ073 PCB REV. 6 +--1 |XX | Component Side +--4 |XX J1 | 1xxx3 | |JP68 |XX | JP70 8--1 |XX | |XX | +-------+ +-------+Term. | | + 5A | + IC | |xx | +-------+ +-------+ |XX | (POSN-P) TP27Ax xTP10A (GND) |XX J3 +---------------------------------------------------------+ +---------------------------------------------------------+ | +--+| | | || | Head Sel #7 3xxx1 |J7|| | SZ074 PCB Fault Jumper > JP4A | || | Switch +--+| | +---+| | | ++--- | +----+ | J4|| | | | | ++----- | | J8 | +---+| | | | +-+| | +----+ J5| || | | || | | || | +-+| | J6+--+ | | +--+ | +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** HITACHI DK511 PRODUCT MANUAL K6600061 REV. 7, 10/01/1985 Jumper Setting ============== Adjustment ---------- There are two types of jumper switches for DK511 as follows: CAUTION 1. Jumper Switches with GREEN connectors: to be used for an assign- ment of unit address and for selection of optional functions, and to be arranged when installing the unit or replacing the PC board. 2. Jumper Switches with BLACK connectors; to be used for adjusting servo control circuits. These need not be readjusted when installing the unit or replacing to a spare PC board since they have already been adjusted at shipment. Even if a readjustment is needed by all means, be sure to make a record of their preset status prior to readjust them for the capability of recovery. Setting of GREEN Jumper Switches -------------------------------- JP68 Drive Select Jumper Switch ------------------------------- There is the jumper switch to select the drive address number. Set up the switch as follows: 8 7 6 5 8 7 6 5 8 7 6 5 8 7 6 5 +-------+ +-------+ +-------+ +-------+ |X o o o| |o X o o| |o o X o| |o o o X| |X o o o| |o X o o| |o o X o| |o o o X| +-------+ +-------+ +-------+ +-------+ 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 Drive 0 Drive 1 Drive 2 Drive 3 As shipped, the jumper pins 1 to 8 is shorted for Drive 0. Jumper for Optional Functions ----------------------------- General Reset Jumper Switch As an optional feature, there is General Reset signal (J1-2 pin) which can be available by the jumper switch (JP70 on SZ073 PCB REV. 3 SZ073 PCB REV. 4 or 5, SZ073 PCB REV. 6 ). Set up the jumper switch as follows: General Reset Jumper Switch SZ073 PCB REV. 3 JP70 JP70 +-+ +-+ |o| J1-2 pin is OPEN |X| General Reset Signal is available |o| |X| +-+ +-+ Primary Optional When shipped the jumper is set to the primary position. General Reset Jumper Switch SZ073 PCB REV. 4 JP70 JP70 +-+ +-+ |X|1 J1-2 pin is OPEN |o| General Reset Signal is available |X|2 |X| |o|3 |X| +-+ +-+ Primary Optional When shipped the jumper is set to the primary position. Write Protect Jumper Switch --------------------------- As an optional feature, there are WRITE PROTECT (J2-7 Pin) and WRITE PROTECTED signal (J2-11 pin) which can be available by the jumper switches (JP113 and JP117). Setting up these jumper switches are as follows: Primary ------- JP113 JP117 10-------6+ +6---4+ JP113 J2-7 pin is connected to J1-16 pin. |o X o o o| |o o o| JP117 J2-11 pin is GND. |o X o o o| |o xxx| +1-------5+ +1---3+ Optional -------- JP113 JP117 10-------6+ +6---4+ JP113 Write Protect signal is available. |o o o o o| |o X o| JP117 Write Protected signal is available. |xxx o o o| |o X o| +1-------5+ +1---3+ When shipped, these jumpers are set in the primary position. JP182A LED Jumper Switch ------------------------ There is the jumper switch (SZ073 PCB REV. 6 ) deactivating the green LCD. Primary Optional ------- -------- +-+ +-+ 1|X| LED activated 1|o| LED deactivated (OFF) 2|X| 2|X| 3|o| 3|X| +-+ +-+ When shipped, this jumper is set in the primary position. Terminator ---------- If the multiple drives are connected in the daisy chain mode, only the last drive must be terminated with a terminator module. When shipped, the terminator module (IC#IC) is installed. Remove it all but the last drive (if the multiple drives in the daisy chain mode). Adjustment Specification (BLACK Jumper) --------------------------------------- NOTE Since adjustment portions are already adjusted when the device is shipped, don't move them unless understanding the prior "CAUTION" of this chapter. JP4A Head Sel #7 Fault Jumper Switch ------------------------------------ (This jumper is available from SZ073 Rev. 7) Write Fault caused by invalid head selection is ignored by this option. If this option doesn't use, the selection of HD#7 causes Write Fault. This option is available on and after SZ073 REV. 7. Primary Optional ------- -------- +-+ JP4A +-+ JP4A 1|o| HD#7 selection 1|x| HD#7 selection doesn't 2|X| causes Write 2|X| causes Write Fault. 3|X| Fault. 3|o| +-+ +-+ When shipped, this jumper is set in the primary position. PLO free-running frequency -------------------------- - Pull J6 Connector and insert Jumper socket in JP164 for allowing the error signal to set at zero. - Turn the power on, and adjust the value of JP117-6 pin within the range of 10 MHz 1% using JP123. - After completion of aforementioned adjustment, turn the power off, insert J6 Connector in the original position, and then pull Jumper Socket out of JP164. - Turn the power on again and ensure that an operation is in normal status (device in READY status).