K L - 3 1 0 0 O C T A G O N I I KALOK NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders | 979| | Capacity form/unform 105/ 120 MB Heads | 6| | Seek time / track 25.0/ 5.0 ms Sector/track | 35| | Controller IDE / AT Precompensation Cache/Buffer 32 KB STATIC RAM Landing Zone Data transfer rate 1.250 MB/S int Bytes/Sector 512 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 10 55 | -40 60 Power: sleep W Humidity % 8 80 | 5 90 standby W Altitude km -0.305 3.048| -0.305 9.000 idle 8.2 W Shock g 8 | 40 seek 10.4 W Rotation RPM 3662 read/write W Acoustic dBA 40 spin-up W ECC Bit MTBF h 100000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** KALOK KL3100 OEM MANUAL VER. 2.0, 16/JULY/1991 P/N 86009-001 A +---------------------------------------------------------+ 12V | |XXGND | Power |XXGND | | 5V | |1X | |XX I | |XX N | |XX T | |XX E | |X* R | |XX F | |XX A | |XX C | |XX E | |XX | |+-+ | Jumper|| | | || |M/S +---------------------------------------------------------++-+ ********************************************************************** J U M P E R S ********************************************************************** KALOK KL3100 OEM MANUAL VER. 2.0, 16/JULY/1991 P/N 86009-001A Jumper Setting ============== GND 40 Pin IDE Connector 12VDC | 5VDC | M/S | +++ | +-----------------+-------------------+ +-+-+ +-------+---------------------------------------------------+ |Power |O O O O O O O O O O O O O O O O O O O O O O O O| |O O O O|1 O O O O O O O O O O O O O O O O O O O O O O O O| +-------+---------------------------------------------------+ -------+ Single Drive in a System O O O |M/S (Factory Setting) O O xxx | -----------+ -------+ Master Drive in a two X O O |M/S drive system O X O O | -----------+ -------+ Slave Drive in a two O X O |M/S drive system O O X O | -----------+ X = CLOSED Two drive system: Drive 1 must be MASTER Drive 2 must be SLAVE Master/Slave Daisy-Chain Configuration -------------------------------------- The KL3100 disk drive ships with one jumper installed in the jumper block header. The jumper is across the top outside pins. This jumper selects a single drive installation. The single drive is Drive 0 (Fixed disk 1 in the system BIOS setup or C:). For a single AT/IDE hard disk drive installation, leave the jumper in the header across these pins. All jumpers removed also works for a single drive installation. For a dual drive daisy-chain installation, the master drive is Drive 0 (fixed disk 1 in BIOS setup or C:). The master drive must have pin pair Master of the jumper block header jumpered. The slave drive is Drive 1 (fixed disk 2 in BIOS setup or D:). The slave must have pin pair Slave of jumper block jumpered. Install no other jumpers in jumper block on the KL3100 disk drive. There should be only one jumper installed per drive. Some mixed vendor master/slave sual drive configurations may not be compatible. ********************************************************************** I N S T A L L ********************************************************************** KALOK KL3100 OEM MANUAL VER. 2.0, 16/JULY/1991 P/N 86009-001 A Notes On Installation ===================== Drive and Host Adapter Installation ----------------------------------- This chapter provides configuration and installation instructions for the Kalok KL3100/AT hard disk drive. Before installing the hard disk, you must first disconnect your AT computer system from AC power out- lets. Required Disk Subsystem Parts ----------------------------- 1. Kalok KL3100/AT hard disk drive P/N 73003-001 2. Kalok 5.25" mounting brackets P/N 83003-001 (black) and faceplate P/N 83003-002 (grey) 3. Kalok 3.5" faceplate P/N 83001-001 (black) P/N 83001-002 (grey) 4. 40-pin AT/IDE hard disk cable Supplied with the Host adapter 5. 34-pin floppy disk drive cable Supplied with the Host adapter 6. Not supplied with Kalok mounting kits, are four standard 6-32 screws. The KL3100 needs the 6-32 screws to mount the drive. The drive mounts with the threaded holes on the bottom or sides. If needed, the AT- style sidemount rails attach to the Kalok 5.25" mounting brackets. Select screw lengths that limit screw penetration into the mounting brackets to 0.13 inches (3.3 mm) max. Notes: 1. In many new AT system cases, 3.5" internal mounting options are available. Some AT cases designs, need AT-style side-mount rails. 2. Embedded AT/IDE systems don't need the PC/AT host adapters. Non- embedded AT/IDE systems need a host adapter. Required Host adapter formatting/Partitioning Software ------------------------------------------------------ 1. To format and partition the disk, you need a bootable DOS diskette version 3.31 or higher. You also need the DOS utilities FDISK and FORMAT programs, in the same DOS version. Interface Connector Part Numbers -------------------------------- P1: AT/IDE Task File (40-pin) Molex 40312 or 3M 3417 P2: Power Supply (4-pin) Molex 8981-4P housing Molex 8980-3 contacts AMP 1-480424-0 housing AMP 60617 contacts P8: Drive HDA ground (1-pin) Molex 187 quick disconnect AMP 62137 quick disconnect Install a Plug to pin 20 on P1. This will prevent an incorrect connection of J1 and P1. Removal of pin 20 of J1 is an industry standard from. AT/IDE Cable Connections ------------------------ Cable connections between the host adapter or the host system should use 28 AWG stranded flat cable, 3M 3365-40, or equivalent. The cable length should not exceed 2 feet. ********************************************************************** F E A T U R E S ********************************************************************** KALOK KL3100 OEM MANUAL VER. 2, 16/JULY/1991 P/N 86009-001 A General Description ------------------- The KL3100 Winchester disk drive is a storage device for a computer system with the industry standard PC/AT or AT/IDE interface. The KL3100 has a formatted capacity of 105.2 megabytes. It uses a rotary band positioner driven by a bipolar stepper motor. The stepper has microstepping error recovery and a feedback sensor. The disk drive operates under the control of a microprocessor to position the read/write heads. The head positioning mechanism design assures that the thermal loops of the positioning system oppose each other. This results in extremely accurate head positioning over the entire operating range. The KL3100 has a magnetic fluid seal. This eliminates spindle motor bearing contamination. The recirculating filter at the periphery of the disks efficiently cleans the head/disk assembly (HDA) air. The filter traps entrained particles. Seek Time --------- +----------------------------------+--------+ | | 3012 | +----------------------------------+--------+ |Track-to-Track msec. typ. | 5 | +----------------------------------+--------+ |One-Third Stroke msec. | 25 | |True average seek msec. | 25 | +----------------------------------+--------+ |Full stroke seek msec. | 50 | +----------------------------------+--------+ |Latency msec. avg. | 8.19 | +----------------------------------+--------+ Drive Formatting ---------------- The KL3100 is factory formatted. The KL3100/AT drive uses cylinder/ head skewing to improve data throughput performance. The format and skewing features of the drive are transparent to the user. Altering the Format during use is not possible. WARNING Remove the Yellow shipping tape from the drive before you apply power.