8 5 1 2 1 A 8 O E M D I A M O N D MAXTOR Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 6569|10585| | Capacity form/unform 5121/ MB Heads 8| 15| | Seek time / track 10.0/ 1.0 ms Sector/track | 63| | Controller IDE / ATA3 Precompensation Cache/Buffer 256 KB MAXCACHE Landing Zone Data transfer rate 8.000 MB/S int Bytes/Sector 512 16.700 MB/S ext PIO4 Recording method RLL 8/9 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 71 Power: sleep 0.6 W Humidity % 5 95 | 5 95 standby 0.8 W Altitude km -0.061 3.048| idle 4.5 W Shock g 20 | 150 seek 5.0 W Rotation RPM 5400 read/write 5.3 W Acoustic dBA 36 spin-up 12.4 W ECC Bit SMART MTBF h 500000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR 85121A8 JUMPER SETTING J1 IDE Connector Jumper J2 Power +----------- ----------++-----------++---------+ | .................... || * * * * || X X X X | | .......... ......... || * * * * * || X X X X | +----------------------++-----------++---------+ ********************************************************************** J U M P E R S ********************************************************************** MAXTOR 85121A8 JUMPER SETTING Jumper Setting ============== +---+---+---+---+---+ Jumper Destination |J50|J48|J46|J44|J42| +-------------------------------------+---+---+---+---+---+ | Master/Slave | | | | | | | Only Drive in single drive system* | J | | | | | | Master in a dual drive system* | J | | | | | | Slave in a dual drive system | O | | | | | +-------------------------------------+---+---+---+---+---+ | Cable Select | | | | | | | Disabled* | | O | | | | | Enabled | | J | | | | +-------------------------------------+---+---+---+---+---+ | 4092 Cylinder Option | | | | | | | Disabled* | | | O | | | | Enabled | | | J | | | +-------------------------------------+---+---+---+---+---+ | Factory Reserved | | | | O | | +-------------------------------------+---+---+---+---+---+ | Factory Reserved | | | | | O | +-------------------------------------+---+---+---+---+---+ J=Jumpered O=Open *=Default Pin 1 J1 IDE Connector | J2 Power +----------- --------|-++-----------+----------+ | .................... || @ * * o |/ \ | .......... ......... || @ o o o o || O O O O | +----------------------++-----------++---------+ | | | | | | | | | | | | | | | | | | J50 Master/Slave -----+ | | | | | | | + +12V (Yellow) J48 Cable Select -------+ | | | | | +-- +12V Return (Black) J46 4092 Cyl Limitation---+ | | | +----- +5V Return (Black) J44 Factory Reserved -------+ | +------- +5V (Red) J42 Factory Reserved ---------+ @ = Default Jumped Positions * = "Spare" Jumper Position o = Default Open Positions ********************************************************************** I N S T A L L ********************************************************************** -ANY DIREC. Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). ********************************************************************** F E A T U R E S ********************************************************************** MAXTOR 85121A8 JUMPER SETTING Power Mode Definitions: ----------------------- Active The drive is spinning and most circuitry is powered on. The drive is capable of responding to read commands in the shortest possible time. Read/Write heads are positioned over the data area. Idle The drive is spinning., the actuator is parked and powered off, and all other circuitry is powered on. The drive is capable of responding to read commands within 40 ms. Read/Write Data is being read from or written to the drive. Spin-up The drive is spinning up following initial application of power and has yet not reached full speed. Maximum current draw lasts one second. Sleep This is the lowest power state. The interface becomes inactive. A software or hardware reset is required to return the drive to Standby. Standby The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires disk access. The time-out value for this mode is programmable. The buffer is active to accept write data.