S T 3 2 1 0 7 N V C A Y M A N SEAGATE NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 4016| | | Capacity form/unform 2147/ MB Heads 10| | | Seek time / track 8.5/ 2.0 ms Sector/track | | | Controller SCSI2 SI/FAST/AV Precompensation Cache/Buffer 512 KB Landing Zone Data transfer rate 6.700 MB/S int Bytes/Sector 512 10.000 MB/S ext Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep W Humidity % 5 95 | 5 95 standby W Altitude km -0.061 3.048| 12.192 idle 8.9 W Shock g 5 | 75 seek 11.9 W Rotation RPM 7200 read/write 10.6 W Acoustic dBA spin-up W ECC Bit MTBF h 1000000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** CONNER CFP-2107S PRODUCT MANUAL 501-071 6/94 PRE-RELEASE REV. A +---------------------------------------------------------+ | +-J1 ++ |XX J2 | | | || |XX | | | || |XX | | | || |XX I | +-+ || |XX N | *+ |XX T | E8++ |XX E | ++ |XX R | (Fuse)F1 xx |XX F | J3 ++ |XX A | +-+ SS ++++++++ || |XX C | | | LED ++++++++ || |XX E | | | E1 ****** E7 || |XX | +-+ E4 RESERVED || | |J6+0E1 *+ |xx || | |XX J4 |+-+0E6 |XX Power +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** CONNER CFP-2107S PRODUCT MANUAL 501-071 6/94 PRE-RELEASE REV. A Jumper Setting ============== Setting the SCSI Bus Address ---------------------------- There are three jumpers available for configuration of the SCSI ID: E1, E2, and E3. OPTIONAL HEADER | +-+ 0E1 | ----+ +-* SCSI ID 1 0E2 | ----+ +-* SCSI ID 2 0E3 | ----+ +-* SCSI ID 4 0E5 | ----+ +-* Disable Spin 0E6 | ----+ +-* LED Driver | +-J6 | PCB +--------------- An optional 2mm pin pitch right angle header is located on the front of the PCBA (opposite the SCSI interface connector) which allows changing the SCSI IDs while the drive is mounted in the system. The header includes three pins, 0E1, 0E2 and 0E3 which can alternatively be used to select the SCSI Bus address. This connector may also be used to cable the SCSI ID select to a remote switch. A receptable connector AMP P/N 111622-1 or equivalent can be used to connect a ribbon cable to this header. +----------+-----------------------+ | SCSI ID | 0E3 0E2 0E1 | | | E3 | E2 | E1 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ NOTE When controlling the SCSI ID remotely, IN (CLOSED) = Ground or TTL Low and OUT (OPEN) = Open or TTL High. Disabling Spin-Up at Power On ----------------------------- A jumper in the E5 location, disables spin up after power-on for applications where spin up sequencing is necessary. An optional 2mm pin pitch right angle header is located on the front of the PCBA (opposite the SCSI interface connector) which can alternatively be used to disable spin up. Disabling spin up on application of power can also be enabled by setting the DSPN bit in MODE SELECT page 00H (Operating Parameters). The Host must issue a Start UNIT command to cause the drive to spin up. +---------+------+---------------------+ |E5 or 0E5| DSPN | Result | +---------+------+---------------------+ | IN | 0 | Spin Disabled | +---------+------+---------------------+ | IN | 1 | Spin Disabled | +---------+------+---------------------+ | OUT | 0 | Spin up on Power On | +---------+------+---------------------+ | OUT | 1 | Spin Disabled | +---------+------+---------------------+ NOTE IN = Ground or TTL Low and OUT = Open or TTL High. Delaying Spin Up at Power On ---------------------------- A jumper in the E6 location, delays spin up on power-up by the value of the drive's SCSI ID multiplied by 4 seconds (i.e. SCSI ID 4 will delay 16 seconds). Delaying spin up on application of power can also be enabled by setting the SDLY bit in MODE SELECT page 00H (Operating Parameters.) +---------+------+---------------------+ | E6 | SDLY | Result | +---------+------+---------------------+ | IN | 0 | Spin Delayed | +---------+------+---------------------+ | IN | 1 | Spin Delayed | +---------+------+---------------------+ | OUT | 0 | Spin up on Power On | +---------+------+---------------------+ | OUT | 1 | Spin Delayed | +---------+------+---------------------+ Disabling the SCSI Bus Parity ----------------------------- SCSI parity is always enabled in both directions, unless the E7 Parity disable jumper is installed. Installing the jumper will cause the drive to ignore SCSI bus Parity In but it will continue to generate SCSI bus Parity Out. Disabling SCSI Bus Terminator Power (TERMPWR) --------------------------------------------- Power to the on-board terminators is provided by the higher of the voltage supplied at Pin #26, J2 or the voltage level at the 5 Volt power input to the drive minus one diode drop. Termination Power to external terminators can be supplied by the drive through Pin #26, J2. The TERMPWR line can be disconnected from the drive by removing Jumper E8. Jumper E8 Result IN TERMPWR (J2, Pin #26) connected to the drive's internal termination power. OUT TERMPWR (J2, Pin #26) open circuit. Setting the Bus Termination --------------------------- This drive provides on-board Alternative 2 active termination for the SCSI bus. The termination resistors, which are contained in two Single Inline Packs (SIPs) should be removed from the drive unless it is a SCSI device at the physical end of the bus. NOTE The TERMPWR output of the drive is protected by a 1 Ampere fuse (F1). If external terminators are being powered from the drive and SCSI bus problems are suspected, verify that the fuse is still operational using a meter. ********************************************************************** I N S T A L L ********************************************************************** CONNER CFP-2107S PRODUCT MANUAL 501-071 6/94, PRE-RELEASE REV. A Notes on Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Mounting the Drive ------------------ The drive is designed to be used in applications where the unit may experience shock and vibrations at greater levels than larger and heavier disk drives will tolerate. The design features which allow greater shock tolerance are the use of rugged heads and media, a dedicated landing zone, closed loop servo positioning and specially designed motor and actuator assemblies. Eight side, or four bottom base mounting points are provided to the customer. The drive is mounted using 6-32 UNC -2B X 0.16 maximum insertion length screws. The system integrator should allow ventilation to the drive to ensure reliable drive operation over the operating temperature range. The drive may be mounted in any orientation. Attaching Power to the Drive ---------------------------- The drive has a 4-pin DC power connector, J4 mounted on the PCB. The recommended mating connector is AMP part number 1-480424-0 utilizing AMP pins, part number 350078-4 or equivalent. SCSI Bus Cable -------------- The cable should meet the following guidelines, particulary with FAST SCSI-2 systems: - Do not route the data cable next to the drive PCB or any other high frequency or large current switching signals. Improper drive opera- tion can result from improper cable routing. - Cable stubs should not exceed 0.1 meter (4 inches). - There should be 0.3 meters (12 inches) of cable between drives. - The total cable length should not exceed 6 meters (20 feet) and may have to be reduced if a mixture of round and flat cable are used. - Do not tightly bundle excess flat cable against each other since this promotes cross coupling of signals on the cable. Use spacers to maintain a minimum of 0.050 inches (1.27mm) gap between cable runs. - Do not clamp the cable tightly against a metal chassis since this will degrade the signal. Use spacers or a non-flammable insulation material to maintain a gap between the chassis and the cable. Spindle Synchronization ----------------------- The spindle rotation of up to 35 drives may be synchronized together by daisy chaining pin 1 to pin 1 and pin 2 to pin 2 on connector J3. The spindles are synchronized using a "floating master" concept, where the drives will synchronize to the first drive to reach full speed. The synchronization tolerance is 1%. External Termination Power -------------------------- Power to the on-board terminators is provided by the higher of the voltage supplied at Pin #26, J2 or the voltage level at the 5 Volt power input to the drive minus one diode drop. The diode prevents back flow of current to the drive. Termination Power to external terminators can be supplied by the drive through pin 26, J2. The TERMPWR line can be disconnected from the drive by removing Jumper E8. Internal Termination -------------------- This drive provides on-board Alternative 2 active termination for the SCSI bus. The termination resistors, which are contained in two Single Inline Packs (SIPs) should be removed from the drive unless it is a SCSI device at a physical end of the bus. Cable Requirements ------------------ A 50 conductor cable no more than 6 meters (19.68 feet) cumulative length with at least 28 AWG wire size and a characteristic impedance of 70 to 100 ohms (84 ohms nominal) is required. Connector Requirements ---------------------- The connector on the drive is a 50-position header which consists of 2 rows of 25 male pins on 0.100 inch centers. The mating connector is a SCSI-2 Non-shielded Alternative 1, A-cable connector. ********************************************************************** F E A T U R E S ********************************************************************** CONNER CFP-2107 PRODUCT MANUAL 501-071 6/94, PRE-RELEASE REV. A Overview of the Drives ---------------------- The CFP2107 series is a family of high performance 3.5-inch low- profile (1.0 inch high) 2.1GB (formatted) disk drives. They all offer 8.5 millisecond average seek time for Reading, 9.0 millisecond seek time for Writing, with an average latency of only 4.17ms. High capacity is achieved by utilizing a zone density recording technique using 15 recording zones at an areal density of 317 Mbits per square inch. These drives feature high performance while maintaining low power consumption to reduce power supply current and system cooling requirements in disk arrays. They are designed to operate on the Small Computer System Interface (SCSI) and are SCSI-2/3 command compatible. The mechanical and major electronic components are identical between the models and differ only in the host interface implementation. Firmware -------- The drive's firmware can be considered in two parts. The first part principally reside in the ROM for the 68HC16 background processor. This processor is responsible for: - starting the spindle motor and maintaining precise rotational speed - controlling track following and actuator motion during seeking - managing background R/W activity - power management - monitoring the overall health of the drive. The interface processor's control microcode resides in both ROM and RAM. The RAM portion of the microcode can be upgraded in the field with using software. The interface processor firmware functions include: - reporting drive status and error conditions to the host - manage operating parameters for the drive - parsing the Command Descriptor Block and checking for illegal fields - converting the LBA to CHS and initiating read and write operations to the background processor - defect management - serial port communications Since parsing/decoding of commands and execution of the Read/Write functions are handled by separate processors, command execution can be overlapped in multiple initiator or Tagged Command Queuing environments. Functions such as seek re-ordering and command coalesc- ing can also be overlapped when the drive is operating with a host environment capable of supporting Tagged Command Queuing. Seek Time --------- +----------------------------------+--------+ | | 2107 | +----------------------------------+--------+ |Track-to-Track msec. typ. | 2 | +----------------------------------+--------+ |Average msec. read | 8.5 | | msec. write| 9 | +----------------------------------+--------+ |Full Track msec. | 18 | +----------------------------------+--------+ |Latency msec. avg. | 4.17 | +----------------------------------+--------+ Error Correction ---------------- The drive uses a three way interleaved 144-bit Reed-Solomon code to perform error correction, plus a 6 bit CRC. For each 512-byte block, the on-the-fly error correction polynominal is capable of correcting: - one error burst of up to 41 bits in length - two error bursts each up to 17 bits in length The miscorrection probability is less than 1 bit in 10(24) bits transfered. ********************************************************************** G E N E R A L ********************************************************************** SEAGATE SUPPORT SERVICES Seagate Technology ------------------ Technical Support Services If you need assistance installing your drive, consult your dealer. Dealers are familiar with their unique system configurations and can help you with system conflicts and other technical issues. If you need additional assistance with your Seagate(r) drive or other Seagate products, use one of the Seagate technical support services listed below. SeaFONE at 1-800-SEAGATE (1-800-732-4283) Seagate's 800 number allows toll-free access to automated self-help services, providing answers to commonly asked questions, troubleshooting tips and specifications for disc drives and tape drives. This service is available 24 hours daily and requires a touch-tone phone. If you need to speak to a technical support engineer, dial this number and listen to the options for technical support. (International callers can also reach this automated self-help service by dialing 408-456-4496). Seagate Technology online services Using a modem, you can obtain troubleshooting tips, free utility programs, drive specifications and jumper settings for Seagate's entire product line. You can also download software for installing and analyzing your drive. SeaNET You can obtain technical information on Seagate drives, Seagate software and much more over the Internet from Seagate's World Wide Web home page (http://www.seagate.com) or Seagate's ftp server (ftp://ftp.seagate.com). You may also send E-mail with your questions to DiscSupport@ Seagate.com or TapeSupport@Seagate.com. SeaBOARD SeaBOARD is a computer bulletin board system (BBS) that contains information about Seagate's disc and tape drive products and is available 24 hours daily. Set your communications software to eight data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers are listed in the following table. BBS Location Modem number United States Disc: 408-434-1080; Tape: 408-456-4415 England 44-1628-478011 France 33 1-48 25 35 95 Germany 49-89-140-9331 Singapore 65-292-6973 Thailand 662-531-8111 Australia 61-2-9756-2359 Taiwan 886-2-719-6075 Seagate CompuServe forum Online technical support for Seagate products is available on CompuServe. To access our technical support forum, type go seagate. This forum provides information similar to that found on SeaBOARD. In addition, you can type questions or browse through previous questions and answers on the forum messages. Seagate Technology FAX services SeaFAX You can use a touch-tone telephone to access Seagate's automated FAX system to receive technical support information by return FAX. This service is available 24 hours daily. Location Telephone number United States 1-800-SEAGATE or 408-456-4496 England 44-1628-894084 Australia 61-2-9756-5170 Seagate technical support FAX You can FAX questions or comments to technical support specialists 24 hours daily. Responses are sent during business hours. Location FAX number United States 408-944-9120 England 44-1628-890660 France 33 1-46 04 42 50 Germany 49-89-1430-5100 Australia 61-2-9725-4052 Singapore 65-293-4722 Hong Kong 852-2368 7173 Taiwan 886-2-715-2923 Korea 82-2-556-7294/4251 Seagate technical support You can talk to a technical support specialist during business hours Monday through Friday for one-on-one technical help. Before calling, note your system configuration and drive model number (STxxxx). There are several technical support phone numbers available for various Seagate products. Location Telephone number United States Please dial 1-800-SEAGATE for the specific product telephone number. (6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M., Pacific time, M-F) England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) France 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 5:00 P.M., M-F) Germany Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00 P.M. to 4:00 P.M., M-F) Tape: 49-89-140-9333 Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F) Singapore 65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00 P.M. to 5:00 P.M., M-F) Hong Kong 852-2368 9918 Taiwan 886-2-514-2237 Korea 82-2-556-8241 SeaTDD 408-944-9121 Using a telecommunications device for the deaf (TDD), you can send questions or comments 24 hours daily and exchange messages with a technical support specialist between 6:00 A.M. to 11:15 A.M. and 12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday. Customer Service Centers Seagate direct OEM, Distribution, System Integrator and Retail customers should contact your Seagate Service Representative for warranty information. Other customers contact your place of purchase. Seagate offers comprehensive customer support for all Seagate drives. Seagate customer service centers are the only facilities authorized to service Seagate drives. These services are available worldwide. Location Telephone number FAX number United States 1-800-468-3472; 405-949-6740 Other Americas (Canada & Brazil) 405-949-6706; 405-949-6738 Mexico 525-546-6965; 525-546-4888 Europe, Middle East & Africa 31-2065-43300; 31-2065-34320 Asia Pacific & Australia 65-485-3595; 65-485-4980 Japan 81-3-5462-2904; 81-3-3462-2979 Seagate, Seagate Technology and the Seagate logo are registered trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD, SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or registered trademarks of Seagate Technology, Inc. or one of its subsidiaries. All other trademarks or registered trademarks are the property of their respective owners.