D B C A - 2 0 6 4 8 0 T R A V E L 6 G IBM Native| Translation ------+-----+-----+----- Form 2.5"/SUPERSLIMLINE Cylinders 11648| | | Capacity form/unform 6400/ MB Heads 4| | | Seek time / track 13.0/ 2.5 ms Sector/track | | | Controller IDE / ATA4 Precompensation Cache/Buffer 512 KB Landing Zone Data transfer rate 10.000 MB/S int Bytes/Sector 512 33.300 MB/S ext UDMA2 Recording method operating | non-operating -------------+-------------- Supply voltage 5 V Temperature *C 5 55 | -40 65 Power: sleep 0.1 W Humidity % 8 90 | 5 95 standby 0.3 W Altitude km | idle 1.0 W Shock g 150 | 700 seek 2.3 W Rotation RPM 4200 read/write 2.0 W Acoustic dBA spin-up 4.7 W ECC Bit DFT ENABLED MTBF h Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** IBM DBCA-206480/204860/203240 INSTALLATIONS +--------------------------------------+ | | | | | | +--------Interface-------------49------+ | 43**********************1 **47 Jumper | 44*************x********* **48 | +------------------------------50------+ + + Pin position 20 is left blank for correct connector insertion. Pin position 47 through 50 are used for drive address setting. ********************************************************************** J U M P E R S ********************************************************************** IBM DBCA-206480/204860/203240 INSTALLATIONS Jumper Setting ============== Drive Address Setting --------------------- A jumper is available at the interface connector to determine the drive address. ---49--47+ * * X | Slave * * X | ---50--48+ ---49--47+ * * * | Master * * * | ---50--48+ ---49--47+ * * * | Cable Selection * xxx | ---50--48+ ---49--47+ * xxx | * * * | RESERVED Never attach a jumper here! ---50--48+ ---49--47+ * X * | NEVER ATTACH A JUMPER HERE!!! * X * | ---50--48+ Cable Selection --------------- Using Cable Selection, the drive address depends on the condition of pin 28 of the AT interface cable. In the case when pin 28 is ground or low, the drive is a Master. If pin 28 is open or high level, the drive is a Slave. Cabling ------- The maximum cable length from the host system to the HDD plus circuit pattern in the host system shall not exceed 18 inches. AT Signal Connector ------------------- The AT signal connector is designed to mate with Dupont part number 69764-044 or equivalent. ********************************************************************** I N S T A L L ********************************************************************** IBM DBCA-206480/204860/203240 INSTALLATIONS Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Performance and error rate will stay within specification limits if the drive is operated in the other permissible orientations from which it was formatted. Thus a drive formatted in a horizontal orientation will be able to run vertically and vice versa. The drive must be securely mounted in the system to prevent motion or vibration during a seek operation or spindle rotation using appropriate screws or equivalent mounting hardware. The recommended mounting screw torque is 3.0 0.5 kgf.cm. The recommended mounting screw depth is 3.0 0.3mm for bottom and 3.5 0.5mm for horizontal mounting. Air Cooling Requirement ----------------------- The host system must provide sufficient air flow across the drive to maintain the temperature at less than 60*C (measured at the centre of the files top cover).