C P - 2 0 2 2 A T CONNER NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 2.5"/SUPERSLIMLINE Cylinders 653| | | Capacity form/unform 21/ MB Heads 2| | | Seek time / track 23.0/ 5.0 ms Sector/track 32| | | Controller IDE / AT Precompensation Cache/Buffer 8 KB Landing Zone Data transfer rate 1.250 MB/S int Bytes/Sector 512 3.750 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5 V Temperature *C 5 55 | -40 60 Power: sleep 0.3 W Humidity % 8 80 | 8 80 standby 0.5 W Altitude km -0.061 3.048| 12.192 idle 1.5 W Shock g 10 | 100 seek 3.0 W Rotation RPM 3433 read/write 3.0 W Acoustic dBA 40 spin-up W ECC Bit INTER.ERROR CORR. MTBF h 40000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** CONNER CP2022 PRODUCT MANUAL 0710399 10/1989, REV. Y2 +------------------------------------------------------+ | |X44 | I |XX Power | +-------+ N |XX +5V 41/42 | +-------+ T |XX GND 43 | E |XX | R |XX | F |X* Position | A |XX 20-Key | C |XX | E |XX | |XX | |XX | E1 E2 |1X | +++ |XX Factory | +++ |XX test +------------------------------------------------------+ points ********************************************************************** J U M P E R S ********************************************************************** CONNER CP2022 PRODUCT MANUAL 0710399 REV. Y2, 10/1989 Jumper setting -------------- Interface Connector/Signal Levels --------------------------------- All signal levels are TTL compatible. A logic "1" is > 2.0 Volts. A logic "0" is from 0.00 Volts to 0.70 Volts. The drive capabolity of each of the inbound signals is described below. +--------------------------------------------------------+ | Pin Signal Pin Signal | +--------------------------------------------------------+ | 01 -Reset 02 GND | +--------------------------------------------------------+ | 03 +Data 7 04 +Data 8 (AT ONLY) | +--------------------------------------------------------+ | 05 +Data 6 06 +Data 9 (AT ONLY) | +--------------------------------------------------------+ | 07 +Data 5 08 +Data 10 (AT ONLY) | +--------------------------------------------------------+ | 09 +Data 4 10 +Data 11 (AT ONLY) | +--------------------------------------------------------+ | 11 +Data 3 12 +Data 12 (AT ONLY) | +--------------------------------------------------------+ | 13 +Data 2 14 +Data 13 (AT ONLY) | +--------------------------------------------------------+ | 15 +Data 1 16 +Data 14 (AT ONLY) | +--------------------------------------------------------+ | 17 +Data 0 18 +Data 15 (AT ONLY) | +--------------------------------------------------------+ | 19 GND 20 Key | +--------------------------------------------------------+ | 21 Reserved 22 GND | +--------------------------------------------------------+ | 23 -IOW 24 GND | +--------------------------------------------------------+ | 25 -IOR 26 GND | +--------------------------------------------------------+ | 27 -DACK (XT ONLY) 28 Reserved | +--------------------------------------------------------+ | 29 +DRQ (XT ONLY) 30 GND | +--------------------------------------------------------+ | 31 +IRQ 32 -IO16 (AT ONLY) | +--------------------------------------------------------+ | 33 +ADDR 1 34 -PDIAG (AT ONLY) | +--------------------------------------------------------+ | 35 +ADDR 0 36 +ADDR 2 (AT ONLY) | +--------------------------------------------------------+ | 37 -CS0 38 -CS1 (AT ONLY) | +--------------------------------------------------------+ | 39 -Active 40 GND | +--------------------------------------------------------+ | 41 5 Volts (Logic) 42 5 Volts (Motor) | +--------------------------------------------------------+ | 43 GND 44 -XT/AT | +--------------------------------------------------------+ MS/CD Master/Slave -------------------- E1 E2 For Master (C Drive) when E1 is CLOSED, place +-+ Jumper as shown. |*| * |*| * +-+ E1 E2 For Slave (D Drive) when E1 is open. Store jumper * * as shown. +-----+ |* *| +-----+ The CP2022 drive is designed to operate either as a master drive (C Drive) or a slave (D Drive) depending on the state of Jumper E1. When E1 is closed, the drive will assume the role of master, when open it will act as the slave. In single drive configurations E1 must be closed. ********************************************************************** I N S T A L L ********************************************************************** CONNER CP2022 PRODUCT MANUAL 0710399 REV. Y2, 10/89 Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ Installation direction ---------------------- The drive may be mounted in any attitude! Recommended Mounting Configuration ---------------------------------- The CP2022 is designed to be used in applications where the unit may experience shock and vibrations at greater levels than larger and heavier disk drives. The design features which allow greater shock tolerance are the use of rugged heads and media, a dedicated landing zone, closed loop servo positioning and specially designed motor and actuator assemblies. Four (4) mounting points are provided to the customer. The drive is mounted from the bottom using 4-40 screws 1/4" max. insertion. The system integrator should allow ventilation to the drive to ensure reliable drive operation over the operating temperature range. For additional vibration isolation, an external suspension system may be used. Interface Connector ------------------- The CP2022 has a 44 pin right angle interface/power connector mounted on the PCB. The recommended mating connector is Dupont part number: 86455-144. The drive is intended to be directly connected through a connector. It is not recommended to solder the connector to a motherboard or other PCBA. Note that through board configuration must allow for 50 pins. Diagnostic Routines ------------------- The microprocessor performs diagnostics upon application of power. If an error is detected, the CP2022 will not come ready. Magnetic Field -------------- The externally induced magnetic flux density does not exceed 6 gauss as measured at the disk surface. Acoustic Noise -------------- 40 dBA max. at 1 meter ********************************************************************** F E A T U R E S ********************************************************************** CONNER CP2022 PRODUCT MANUAL 0710399 REV. Y2, 10/89 Key Features ------------ The CP2022 is a high performance 2.5 inch low-profile (0.69") 21.4 megabyte (formatted) disk drive with average seek time not do exceed 23ms which is designed to operate on IBM PC/XT & PC/AT or equivalent computers. The drives feature a low 5V power requirement and high shock resistance, enabling battery operation in portable environments. - 2.5" Form factor - Single 5 Volt supply - Low power requirements - 5.5 oz - High performance rotary voice coil actuator with embedded servo system. - Single connector for power & interface - Run length limited code (2/7) - High shock resistance - Internal air filtration system - Sealed HDA - Automatic actuator latch over data free landing zone during standby mode or power-down - Microprocessor-controlled diagnostics routines that are auto- matically executed at start-up. - Automatic error correction and retries - Block size 512 bytes - PC XT/AT Interface (interface selectable) - 1:1 sector interleave - Look Ahead Read Capability - 8K Buffer AT Mode ------- The Host addresses the drive using programmed I/O. This method requires that the desired register address be placed on the three address lines A2-A0, a proper drive chip select is asserted and read or write strobe (-IOR/-IOW) is given to the chip. The Host generates two independent chip selects on the interface. The high order chip select, -CS1, is used to access register 3F6 or 3F7. The low order chip select, -CS0, is used to address registers 1F0 - 1F7. The Host data bus 15-8 is only enabled when I016 enable is active and the Host is addressing the data register for transferring data and not the ECC bytes which are only transferred if the operation is read or write long. XT Mode ------- The Host addresses the drive using programmed I/O. This method re- quires that the desired register address be placed on the address lines A1 - A0, a proper drive select is asserted and a read or write strobe (-IOR/-IOW) is given to the drive. The drive is normally decoded at base address 320H. Seek Times ---------- +----------------------------------+--------+ |Physical track to track max. | 5 ms | +----------------------------------+--------+ | AT INTERFACE Average msec. | 23 | | Average msec. max. | 40 | +----------------------------------+--------+ |Latency msec. avg. | 8.7 | +----------------------------------+--------+ Functional Description ---------------------- The CP2022 contains all necessary mechanical and electronic parts to interpret control signals, position the recording heads over the desired track, read and write data, and provide a contaminant free environment for the heads and disks. Read/Write and Control Electronics ---------------------------------- One integrated circuit is mounted within the sealed enclosure in close proximity to the read/write heads. Its function is to provide one of two head selection, read preamplification, and write drive circuitry. The single microprocessor controlled circuit card provides the remaining electronic functions which include: - Read/Write Circuitry - Rotary Actuator Control - Interface Control - Spin Speed Control - Dynamic Braking - Power Management At power down or the start of STANDBY MODE the heads are auto- matically retracted to the inner diameter of the disk and are latched and parked on a landing zone that is inside the data tracks. Drive Mechanism --------------- A brushless DC direct drive motor rotates the spindle at 3433 RPM. The motor/spindle assembly is balanced to provide minimal mechanical runout to the disks and to reduce vibration of the HDA. A dynamic brake is used to provide a fast stop to the spindle motor when power is removed, or upon initiation of STANDBY MODE. Air Filtration System --------------------- Within the sealed enclosure, a 0.3 micron filter which provides a clean environment for the heads and disks. Head Positioning Mechanism -------------------------- The two read/write heads are supported by a mechanism coupled to the voice coil actuator. Read/Write Heads and Disks -------------------------- Data is recorded on 65mm diameter disk through two miniature thin film heads. Error Correction ---------------- The CP2022 performs internal error correction. The error correction polynominal is capable of correcting one error burst with a maximum of 8 bits per 512 byte block. Reliability and Maintenance --------------------------- MTBF 40,000 hours POH (population is min. of 100 units) MTTR 10 minutes typical Preventive Maintenance None Component Design Life 5 years