ACTIONTEC ELECTRONICS, INC.

56K X2 DATA/FAX

Card Type

Modem (asynchronous)

Chipset

Unidentified

Maximum Data Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

Bell 103A, 212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34

U.S. Robotics x2

Fax Modulation

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

8-bit ISA

Card Size

Full height, half length

CONNECTIONS

Function

Label

Function

Label

Telephone line out

CN1

Telephone line in

CN2

USER CONFIGURABLE SETTINGS

Setting

Label

Position

í Plug-N-Play enabled

J3/C

Open

Plug-N-Play disabled

J3/C

Closed

SERIAL PORT ADDRESS SELECTION

Setting

J3/A

J3/B

3F8h (COM1:)

Closed

Closed

2E8h (COM2:)

Open

Closed

3F8h (COM3:)

Closed

Open

2E8h (COM4:)

Open

Open

í Plug-N-Play

Open

Open

INTERRUPT SELECTION

Setting

J2/A

J2/B

J2/C

J2/D

J2/E

2

Closed

Open

Open

Open

Open

3

Open

Closed

Open

Open

Open

4

Open

Open

Closed

Open

Open

5

Open

Open

Open

Closed

Open

7

Open

Open

Open

Open

Closed

í Plug-N-Play

Open

Open

Open

Open

Open

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, F, H, L, M, O, Q, V, X, Y, Z

&C, &D, &F, &G, &P, &R, &S, &T, &W, &Z

S-Registers

The S-registers are unidentified.

Note: See MHI help file for complete information.

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] &Yn [cmds]

Description:

Configures action of break signal.

Command

Function

&Y0

Break empties buffer.

í &Y1

Break empties buffer and is sent immediately.

&Y2

Break does not empty buffer and is sent immediately.

COMPRESSION MODE

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Selects the type of data compression that will be used.

Command

Function

&K0

Data compression disabled.

í &K1

Auto-detect compression mode.

&K2

Data compression enabled.

&K3

MNP5 data compression only enabled.

CONNECTION SPEED LOWER LIMIT

Type:

Configuration

Format:

AT [cmds] &Un [cmds]

Description:

Sets slowest allowed connection speed if &N is set to 1 or higher.

Command

Function

í &U0

No minimum connect speed.

&U1

Set minimum connect speed to 300bps.

&U2

Set minimum connect speed to 1200bps.

&U3

Set minimum connect speed to 2400bps.

&U4

Set minimum connect speed to 4800bps.

&U5

Set minimum connect speed to 7200bps.

&U6

Set minimum connect speed to 9600bps.

&U7

Set minimum connect speed to 12Kbps.

&U8

Set minimum connect speed to 14.4Kbps.

&U9

Set minimum connect speed to 16.8Kbps.

&U10

Set minimum connect speed to 19.2Kbps.

&U11

Set minimum connect speed to 21.6Kbps.

&U12

Set minimum connect speed to 24Kbps.

&U13

Set minimum connect speed to 26.4Kbps.

&U14

Set minimum connect speed to 28.8Kbps.

&U15

Set minimum connect speed to 31.2Kbps.

&U16

Set minimum connect speed to 33.6Kbps.

&U17

Set minimum connect speed to 33.3Kbps.

&U18

Set minimum connect speed to 37.3Kbps.

&U19

Set minimum connect speed to 41.3Kbps.

&U20

Set minimum connect speed to 42.6Kbps.

&U21

Set minimum connect speed to 44Kbps.

&U22

Set minimum connect speed to 45.3Kbps.

&U23

Set minimum connect speed to 46.6Kbps.

&U24

Set minimum connect speed to 48Kbps.

&U25

Set minimum connect speed to 49.3Kbps.

&U26

Set minimum connect speed to 50.6Kbps.

&U27

Set minimum connect speed to 52Kbps.

&U28

Set minimum connect speed to 53.3Kbps.

&U29

Set minimum connect speed to 54.6Kbps.

&U30

Set minimum connect speed to 56Kbps.

&U31

Set minimum connect speed to 57.3Kbps.

CONNECTION SPEED UPPER LIMIT

Type:

Configuration

Format:

AT [cmds] &Nn [cmds]

Description:

Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed.

Command

Function

í &N0

No maximum connect speed.

&N1

Set maximum connect speed to 300bps.

&N2

Set maximum connect speed to 1200bps.

&N3

Set maximum connect speed to 2400bps.

&N4

Set maximum connect speed to 4800bps.

&N5

Set maximum connect speed to 7200bps.

&N6

Set maximum connect speed to 9600bps.

&N7

Set maximum connect speed to 12Kbps.

&N8

Set maximum connect speed to 14.4Kbps.

&N9

Set maximum connect speed to 16.8Kbps.

&N10

Set maximum connect speed to 19.2Kbps.

&N11

Set maximum connect speed to 21.6Kbps.

&N12

Set maximum connect speed to 24Kbps.

&N13

Set maximum connect speed to 26.4Kbps.

&N14

Set maximum connect speed to 28.8Kbps.

&N15

Set maximum connect speed to 31.2Kbps.

&N16

Set maximum connect speed to 33.6Kbps.

&N17

Set maximum connect speed to 33.3Kbps.

&N18

Set maximum connect speed to 37.3Kbps.

&N19

Set maximum connect speed to 41.3Kbps.

&N20

Set maximum connect speed to 42.6Kbps.

&N21

Set maximum connect speed to 44Kbps.

&N22

Set maximum connect speed to 45.3Kbps.

&N23

Set maximum connect speed to 46.6Kbps.

&N24

Set maximum connect speed to 48Kbps.

&N25

Set maximum connect speed to 49.3Kbps.

&N26

Set maximum connect speed to 50.6Kbps.

&N27

Set maximum connect speed to 52Kbps.

&N28

Set maximum connect speed to 53.3Kbps.

&N29

Set maximum connect speed to 54.6Kbps.

&N30

Set maximum connect speed to 56Kbps.

&N31

Set maximum connect speed to 57.3Kbps.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays modem properties.

Command

Function

I0

Displays product identification code.

I1

Tests and displays ROM checksum result.

I2

Tests and displays RAM checksum result.

I3

Displays product identification.

I4

Displays current command settings.

I5

Displays current NVRAM settings.

I6

Displays current connection’s statistics.

I7

Displays product configuration.

ERROR CORRECTION MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects active error correction protocols.

Command

Function

&M0

Normal mode only.

í &M4

Auto-detect mode.

&M5

Error correction mode only.

EXTENDED RESULT CODES

Type:

Configuration

Format:

AT [cmds] &An [cmds]

Description:

Selects extended result codes.

Command

Function

&A0

Extended result codes disabled.

&A1

Error correction result codes enabled.

&A2

V.32 result code enabled.

í &A3

Error correction and compression result codes enabled.

FLOW CONTROL - MODEM-TO-MODEM

Type:

Configuration

Format:

AT [cmds] &In [cmds]

Description:

Selects the type of modem-to-modem flow control used.

Command

Function

í &I0

Software flow control disabled.

&I1

XON/XOFF pass-through enabled.

&I2

XON/XOFF pass-through disabled.

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] &Hn [cmds]

Description:

Sets type of flow control used by modem.

Command

Function

&H0

Flow control disabled.

í &H1

CTS/RTS flow control enabled.

&H2

XON/XOFF flow control enabled.

&H3

CTS/RTS and XON/XOFF flow control enabled.

LOCK SERIAL PORT

Type:

Configuration

Format:

AT [cmds] &Bn [cmds]

Description:

Sets operation of serial port speed.

Command

Function

&B0

Serial speed follows connect speed.

í &B1

Serial speed locked.

&B2

Serial speed locked in error correction mode only.